- Remove the top cover, fill water into the water tank, and put the top cover back on. You can also take the water tank out and fill water directly into the tank, and put the water tank back into the main base.
- The display will light up and it beeps one time. 1 second later, the display will turn off, and the “on/off” button will turn red, meaning the humidifier is in standby mode.
- Touch the “on/off” button, the display will light up, and it will start to work in AUTO mode. The display shows the auto symbol and current humidity. 10 seconds later, the display shows current temperature, and then change into humidity. Current temperature and humidity showing will change once every minute.
- Humidifier will decide running humidity based on current temperature as below;
| Temperature of the air, degrees Celsius |
≤19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 ≥37 |
| Humidity (%) | 65 60 58 57 55 53 50 48 45 43 40 38 36 35 34 32 31 30 25 |
- Constant humidity: touch the HUMIDITY button and you can select the humidity from 30%RM to 75%. Touch the button once and it will increase by 5%RH each time. When it reaches 75%, touch again and the display will show “—” and the humidifier will go back to AUTO mode. After setting the preferred humidity, humidifier will keep the memory and confirm by flashing 3 seconds. Once the display switches to show current humidity, it means that the setting is finished, “%” will flash on the display.
- When setting humidity is 1%RH~9%RH higher than current humidity, mist output speed will run by the lowest (the first) speed.
- When setting humidity is 10%RH~15%RH higher than current humidity, mist output speed will run by the middle (the third) speed.
- When setting humidity is 15%RH higher than current humidity, mist output speed will run by the highest (the fifth) speed.
- When current humidity is higher than setting humidity, humidifier will turn into sleep state. Once current humidity is 3%RH lower than setting humidity, humidifier will re-work in previous working mode till water shortage.
- Mist output speed is adjustable under constant humidity function.
-
Night mode: Long press the humidity button for 2 seconds to shut down
the water tank indicator light and display. Only the red On/off button will
show. Press any button to wake up the light and display. -
Timer: There is 12 timer settings: 1-12. Touch the TIMER button and the display will show the timer setting from 1-12 in sequence. For example
“1H”. Once you have found your preferred time setting, do not operate
it for 3 seconds, the time will stop flashing and the timer is set. The timer
shows the rest of the operating time every minute. Press the timer button
for 2 seconds to cancel the operation. -
Heat/Ions: Touch the Heat/Ions button once to start the heating function.
The display shows the heating symbol . Warm mist will come out after
10-15 minutes. Touch the button again to start the plasma function. The
plasma symbol will show on the display. Touch the button again to shut
down the heating function. Touch the button one more time to shut down
the plasma function. Long press the heat/Ions button to tun on/off water
tank indicator light. -
Mist output speed: Touch the bar to enter manual mode.
Slide from MIN to MAX to select your preferred mist output speed. Sliding
from left to right will increase the speed, sliding from MAX to MIN will
decrease the speed. The display shows the selected speed from 1-5. -
Auto shut down: If there is not enough water in the water tank to keep the
humidifier going, the humidifier will automatically stop working and stay
at standby mode. The water shortage symbol will show on the display.
Refill the water tank and press the on/off button to turn the humidifier on
again. If there is too much water in the basin, the display shows EF, and
it will automatically stop working. Pour out some of the excess water and
put the water tank back into the main base, switch it on and it will work as
normal.